Brake failure of Petrol Car is a problem that many car owners often encounter when braking. Once this happens, many people will panic. Therefore, the key to avoiding this problem is normal maintenance. Now, the Honda Car brake pad manufacturer will teach you several methods to self-check the brake pads.
1. Look at the thickness
The thickness of Honda Car brake pads is usually about 1.5 cm. As friction continues during use, the thickness will gradually become thinner. Professional technicians suggest that when the thickness of the Honda Car brake pad is only 1/3 of the original thickness (about 0.5 cm), the owner should increase the frequency of self-inspection at any time and prepare for replacement.
Of course, due to the design of the wheel hub, various models do not have the conditions for visual inspection, so the tire must be removed to complete.
Each brake lining has a raised mark on both sides. The thickness of the mark is approximately two to three millimeters. This is also a limitation of replacing thin brake discs. If the thickness of the brake lining is parallel to this mark, it must be replaced.
Therefore, when the thickness of the brake lining is close to the mark, the car owner must always observe and prepare, but if the tire is not removed, it is difficult to observe accurately with the naked eye. At present, when the brake pads of Petrol Car are too thin, many models of instruments are equipped with handbrake lights. Following the prompts, it's more convenient than self-examination.
2. Listen to the sound
If the brakes make a harsh sound of "iron rubbing iron" (this may also be caused by the running-in of the Honda Car's brake pads at the beginning of installation), the Honda Car's brake pads must be replaced immediately. Since the limit marks on both sides of the brake lining directly rub against the brake disc, it can be proven that the brake lining has exceeded its limit.
In this case, replacement of the brake lining must be accompanied by inspection of the brake disc. When this sound occurs, the brake rotor is usually damaged. Even if the brake pads of Petrol Car are replaced with new ones, the noise cannot be eliminated. In severe cases, the brake disc needs to be replaced.
In addition, hard spots will appear on the brake pads of some inferior Petrol Car, which will also produce abnormal noise. Generally, the abnormal noise produced by this method will disappear and disappear after a period of time.
3. Feeling intensity
If the brakes are applied too hard, the brake pads of Petrol Car may basically lose friction and must be replaced at this time, otherwise serious accidents may occur.
The thickness of Honda Car brake pads is usually about 1.5 cm. As friction continues during use, the thickness will gradually become thinner. Professional technicians suggest that when the thickness of the Honda Car brake pad is only 1/3 of the original thickness (about 0.5 cm), the owner should increase the frequency of self-inspection at any time and prepare for replacement.
Of course, due to the design of the wheel hub, various models do not have the conditions for visual inspection, so the tire must be removed to complete.
Each brake lining has a raised mark on both sides. The thickness of the mark is approximately two to three millimeters. This is also a limitation of replacing thin brake discs. If the thickness of the brake lining is parallel to this mark, it must be replaced.
Therefore, when the thickness of the brake lining is close to the mark, the car owner must always observe and prepare, but if the tire is not removed, it is difficult to observe accurately with the naked eye. At present, when the brake pads of Petrol Car are too thin, many models of instruments are equipped with handbrake lights. Following the prompts, it's more convenient than self-examination.
2. Listen to the sound
If the brakes make a harsh sound of "iron rubbing iron" (this may also be caused by the running-in of the Honda Car's brake pads at the beginning of installation), the Honda Car's brake pads must be replaced immediately. Since the limit marks on both sides of the brake lining directly rub against the brake disc, it can be proven that the brake lining has exceeded its limit.
In this case, replacement of the brake lining must be accompanied by inspection of the brake disc. When this sound occurs, the brake rotor is usually damaged. Even if the brake pads of Petrol Car are replaced with new ones, the noise cannot be eliminated. In severe cases, the brake disc needs to be replaced.
In addition, hard spots will appear on the brake pads of some inferior Petrol Car, which will also produce abnormal noise. Generally, the abnormal noise produced by this method will disappear and disappear after a period of time.
3. Feeling intensity
If the brakes are applied too hard, the brake pads of Petrol Car may basically lose friction and must be replaced at this time, otherwise serious accidents may occur.